LavorService

DOES NOT START

• Check that the electric plug is inserted properly into the socket
...also check the extension connection, if this has been used
• His the switch turned ON ?
• Has the water faucet been opened before turning the switch to ON ?

NO PRESSURE OR LESS PRESSURE THAN USUAL

• is the conical filter located at water intake, inside the pump shell,
   perfectly clean and free from obstruction ?
• is the nozzle at the end of the pipe clear ?..use the steel pin provided or compressed air from the nozzle
   inwards to try to clear it

• does the nozzle have a high/low pressure device ?.if so, try to pull the end of the nozzle (head) towards oneself
   to activate high pressure instead of low pressure?
• if the water being used is from the internal well, try using municipal water mains

IT SWITCHES OFF AND ON CONTINUOUSLY WHILE IN USE

• is the nozzle at the end of the pipe perfectly clear?..use the steel pin provided
or compressed air from the nozzle inwards to try to clear it ?

IT SWITCHES OFF AND ON CONTINUOUSLY WHILE NOT IN USE

• does the machine have any water leaks ?..if so, check whether the "Gardena"-type rapid connection
is fully tightened or if it has been mounted askew?

IT SWITCHES OFF DURING PROLONGED USE, AFTER 1 HOUR OF WORK

• is there enough electricity supplying the home ?.has the counter tripped ? Switch off all other electrical
appliances when using the water cleaner.

• the engine switches off suddenly but the counter does not ?.an unsuitable extension has been used with the
    water cleaner.   See technical table for the use of recommended electrical extensions.
   Or the thermal motor protection has inserted.
    Wait for the time necessary (generally 15 minutes) for it to cool down and then continue working.

THE HIGH PRESSURE TUBE HAS PARTS THAT SEEM WORN

• parts of the high pressure tube seem worn so that the white internal cladding can be seen ?
   .do not worry, the tube has no defect, it is normal wear from friction against the tubes.
   Be sure to unwind the tube completely each time it is used, ensure that there are
   no "eyehole" or "circle" folds.


	Catalogue Applications Assistenza Use and Maintenance Manual Lavor Club Suggestions News Site Map Reserved Area
	Assistenza Hobby Assistenza Professionale Decalogo Tecnico Organizzazione e Contatti
	HOME > AFTER-SALES SERVICE > TECHNICAL INFORMATION > WATER CLEANERS DOES NOT START • Check that the electric plug is inserted properly into the socket ...also check the extension connection, if this has been used • His the switch turned ON ? • Has the water faucet been opened before turning the switch to ON ? NO PRESSURE OR LESS PRESSURE THAN USUAL • is the conical filter located at water intake, inside the pump shell, perfectly clean and free from obstruction ? • is the nozzle at the end of the pipe clear ?..use the steel pin provided or compressed air from the nozzle inwards to try to clear it • does the nozzle have a high/low pressure device ?.if so, try to pull the end of the nozzle (head) towards oneself to activate high pressure instead of low pressure? • if the water being used is from the internal well, try using municipal water mains IT SWITCHES OFF AND ON CONTINUOUSLY WHILE IN USE • is the nozzle at the end of the pipe perfectly clear?..use the steel pin provided or compressed air from the nozzle inwards to try to clear it ? IT SWITCHES OFF AND ON CONTINUOUSLY WHILE NOT IN USE • does the machine have any water leaks ?..if so, check whether the "Gardena"-type rapid connection is fully tightened or if it has been mounted askew? IT SWITCHES OFF DURING PROLONGED USE, AFTER 1 HOUR OF WORK • is there enough electricity supplying the home ?.has the counter tripped ? Switch off all other electrical appliances when using the water cleaner. • the engine switches off suddenly but the counter does not ?.an unsuitable extension has been used with the water cleaner. See technical table for the use of recommended electrical extensions. Or the thermal motor protection has inserted. Wait for the time necessary (generally 15 minutes) for it to cool down and then continue working. THE HIGH PRESSURE TUBE HAS PARTS THAT SEEM WORN • parts of the high pressure tube seem worn so that the white internal cladding can be seen ? .do not worry, the tube has no defect, it is normal wear from friction against the tubes. Be sure to unwind the tube completely each time it is used, ensure that there are no "eyehole" or "circle" folds.